Відео

Word of caution! I tried these in my 02 Jeep Grand Cherokee Laredo and after installing, it smoked like I was spraying for mosquitoes! So I had to go back to the single hole without any issues with smoke like before.

Think make duel polarity lights now. So you do have to mess around so much and see which ones need to be turned

beautiful ruger 😳

Thanks for telling me about the white being cheaper in my state front lights have to be white only !

Do you have any of the diamond coating lube for sale? I’d love to get more

Hi, Mike. How come no recent videos? You still got the TJ, right?

How about the clock on the top?

I'm going to do exactly what you did with my 95' GT. Your videos help a lot, thank you!

Are you loosening the screw to make it go down or tightening?

your jeep is screaming for love when you turn it on but you're worried about your dash lights?

question i have a 2003 ls 430 i took out the dash but for some reason the bulbs aren’t in the back like most models of cars i tried opening it front and back but still couldnt seem too find em

Great video. I’m doing this to mine this weekend ON. Y 2.5 Tj

Is it necessary to take out radio (upper din) or can you just remove bezzel by removing component in lower din and then pull climate control component and change bulbs?

I’ve seen u reply so maybe u can help me lol I installed new lights into my 99 cobra but while I was at it I swapped the odometer face to the terminator face but I took the needles off and now the needles either get stuck in place or they don’t move. Any tips on how to fix? Thank you

What about the hvac lights? My dash lights work great but my hvac lights aren’t on at all.

this is too much work for something that can fail in a year. And honestly Green or Blue is bad for your night vision. Red would be best, low spectrum lighting helps keep your night vision.

Good job, also I’ve had my high beams not stay on before like at the end of this video, thought it was the fuse, but it was the wiring in the light switch Can you post the link for the heating and shifter led light switch you did?

Mike Golden Garage thank you feeling the FAST SIMPLE Video... HELPED me A LOT for my 2009 Dodge Nitro. Dodgr Nitro "Grill Removal" Is REQUIRED to Even Remove/Replace LED/Halo Head Lamps. EZ-PZ to "Route Wires" on ALL 2008-2012 Dodge Nitros.

Im from bensenville il. Cheers

Why don't you make videos anymore?

What kind of wire can I use as an extension. Does it need to be a specific gauge or will any low voltage stereo wire work

nice car

Bon jours j'ai un problème de cliquetis moteur sur une jeep wrangler tj 2.5i 4cilindre pourriez vous m'aider svp merci

LED also has color temperature with narrow range. This means that the gauge needles may not conduct/reflect the LED light if the color temp. range is off. Users might try different kinds of LED bulbs to find the best effect for yourself.

Nice job! Like the upgrade! May do it to mine not sure!

Put a new napa starter on my jeep. It sounds really weird when it starts.

Amazingg

That looks amazing and I would love to do my truck like that. How did you get the blue background with the white numbers

I just watched your video hoping to learn how to wire my halo lights but you skip the part I need to know which is how you connect the red and black wires! ! ! ! 😡😡😡

I'm buying the Oracle headlamps without the halo. I just want brighter, farther reaching headlamps as I drive home from work at night on the highway and I don't need all the bells and whistles. Just something that I can see better at night.

Are the needles ran off of the 194 blue bulbs? Or do they have their own bulbs?

Omg those 4 cyl wranglers suck so bad ...

I wear my sunglasses at night also

Verry verry good job sir me gujrat India se meter repair vala

What year jeep do u have I'm look for part # for the injectors i have a 1997 2.5L

Can you tell me how to change the map light bulbs in my 2002 Mustang convertible. The lights are in the rear view mirror but I cannot find anything on how to replace them.

Are those not upside down cause high beam on the bottom

Hello I hope u Can please help :( So I was gonna change the LED’s for my 95 GT’s gauge cluster and well it had aftermarket white faces the previous owner had installed. I had to remove the needles but now my needles are off… my speed, tach, fuel are off. My battery and fuel pressure are working perfectly. Any help or advice to fix the other three? :/ I’m told to fill the tank to full and put the needle there and then just use a gps to check for speed and tach well I pretty much know where mine idles around 800-900.

😠😠😠 What the hell is everyone talking about??? She showed nothing about connecting the wires!

Correct me if I have not been listening properly but I don't recall you stating the model numbers of these replacement bulbs. There appears to be two different types of bulbs apart from the colours eg: main instrument lights & smaller warning lights, high beam, turn indicators etc, etc!! NO use me even thinking about changing these unless I know what LED bulbs to buy in the first instance!! Sadly this video has not helped me very much!!

what keeps the odometer reading memory while the dash is out?

My odometer light is out. Where on the cluster is the light for the odometer? Thanks.

Where did you plug that wire at that came with the overlay? Only seen that you grounded it.

Oneside of mine is not lighting up. What could be the cause?

What year Jeep is this in the video? I have an 04 TJ that does not have the driver side tumble seat and I’ve been wanting to swap it out, but not sure if it would work. I hate how they changed it to only having the passenger side as the tumble forward seat from 03-06

Verry verry good job Sir

Wow - TERRIBLE WIRE ROUTING. You've placed single-wall (hot) wires through small openings with sharp edges. Engine and road vibration will easily cut through the insulliation shorting them out and creating a total mess. NOT GOOD. Better is to use nylon spacing clips.

love how this was recomended to me wanna do this to mine but fit the ZR guage in to my R25

Question. Mine is an 03 gt. Dimmer looks different and I have a black and red wire. What color do I splice the red one too?

What did you use for the lube for the o-rings? Or what can you use